• Sign Up! To view all forums and unlock additional cool features

    Welcome to the #1 Dodge, Jeep and RAM Forum dedicated to FCA owners and enthusiasts. Register for an account, it's free and it's easy, so don't hesitate to join the SRT Forum today!


What did you do to your Hellcat today?

1971demon

Poster Club Hall of Fame
Founding Member
Member ID
#1122
Messages
29,024
Reactions
62,352
Likes
352
City
Orchard Park
State
NY
Country
United States
Vehicle
2018 Demon 2016 Hellcat

1971demon

Poster Club Hall of Fame
Founding Member
Member ID
#1122
Messages
29,024
Reactions
62,352
Likes
352
City
Orchard Park
State
NY
Country
United States
Vehicle
2018 Demon 2016 Hellcat
Here is what I have on both cars with 305's, except this paint config is apparently no longer available in 10.5. The pockets were black and I repainted them to gray.

https://factoryreproductions.com/pr...lcat-replica-wheels-gloss-black-machine-face/

Some of the other "slingshot" wheels are available in 10.5. I am very happy with them. You can always have a wheel repair shop refinish the wheels to match your wheels. Here is the 10.5" FR next to the OEM.

View attachment 173600
I still have my stock Brass Monkeys and tires boxed up somewhere...from my HC...(not sure why)...
 


Jimmy N.

6000 Posts Club
Founding Member
HFCOTM
Member ID
#996
Messages
6,664
Reactions
12,403
Likes
402
City
Lumberton
State
NM
Country
United States
Vehicle
'18 Challenger
I still have my stock Brass Monkeys and tires boxed up somewhere...from my HC...(not sure why)...
Why? Because the wheels don't go bad.

Give the tires to someone who doesn't know about date codes.
 


1971demon

Poster Club Hall of Fame
Founding Member
Member ID
#1122
Messages
29,024
Reactions
62,352
Likes
352
City
Orchard Park
State
NY
Country
United States
Vehicle
2018 Demon 2016 Hellcat
Why? Because the wheels don't go bad.

Give the tires to someone who doesn't know about date codes.
I was thinkin the same thing bout the tires...nobody I know checks the dates....
 


DGatzby

8000 Posts Club
Founding Member
Premium Account
U.S. Air Force Veteran
Donating Member
HFCOTM & HFCOTY
Member ID
#797
Messages
8,391
Reactions
51,884
Likes
402
City
SW Twin Cities
State
MN
Country
United States
Vehicle
2019 Dodge Challenger Redeye WB
Being the springs were in and out that could have changed it. Going minus 1 (if 5 tab go to 4) on the right side may get you close. I aim for -.25 camber, toe in around .10
Yesterday I put a 4mm in the left side (shorter arm length) from a 6mm that was in it. Thinking I want the slight negative camber equal on each side. Only moved the top arm, loosened the front arm in case there may have been about a hair of any adjustment play. Did not bother to do any measurements. Then drove it. Well at 50 degrees IDK. It basically scared me, I’ll admit a couple of times. SOB has some incredible power and at 50 degrees even the big meats are interesting to control. I think it is “tweaked” good enough.:ROFLMAO: Dropping it down at low speed, a few Track Mode wicked shifts with plenty of subsequent wheel spin, and a couple medium high speed “pedaled” pulls all seem good. That is enough until we can drive it 120 miles to the north of here prepped for some serious shit on a warmer day with even better rubber. She is a good street hot rod until then, and is ready to rumble as necessary.
View attachment IMG_2230.jpeg
 




Top